Move the mouse pointer over the items in the tables below to see photos and descriptions, then click to go to the page.
Part # | Description | Qty |
AWR | Allen Wrenches | 2 |
PBY | Battery Box | 1 |
BPR | Knee Bumper | 1 |
CH | Carry Handles | 2 |
F | Front Boards | 2 |
FPIN | Front Pins | 2 |
HTL | High Side Boards | 1 |
HTR | High Side Boards | 1 |
HS | Hand Screw (for SLT) | 1 |
LT | Low Side Boards | 2 |
PC | Power Cord | 1 |
PP | Push Posts | 2 |
S | Large Seat | 1 |
SLT | 4-way Level Head | 1 |
ST | Small Seat | 1 |
TLW | Pneumatic Tires | 4 |
TSW | Pneumatic Tires | 4 |
Model 10 Dolly
Standard Rental Package
The Standard Rental Package includes all the accessories shown in the Standard Rental Package table on the left.
Allen Wrenches
Allen Wrenches (AWR) are used to change the Level Heads, Wheels and other optional accessories on the Dolly. The Allen Wrenches are stored in the Knee Bumper (BPR). The Model 9 dolly comes with one Allen Wrench. The Model 10 and model 11 dollies have two.
Battery Box
The Battery Box (PBY) is a removable compartment located under the right-hand side of the Dolly's frame. It can accommodate a variety of portable camera batteries. Inside dimensions: 16.3 inches (41.4 cm) wide x 8 inches (20.3 cm) high x 6.2 inches (15.7 cm) deep.
Knee Bumper
The Knee Bumper (BPR) is a safe, soft cushion that assists the operators when push starting the Dolly. The Knee Bumper has holes for storing Allen Wrenches (AWR), Front Pins (FPIN) and other items.
Carry Handles
Carry Handles (CH) are used for properly lifting the front of the Dolly when transporting or placing it on our Scooter Board (SCO), Track or similar products.
Front Boards
Front Boards (F) are used to create a standing platform for camera operators and/or assistants, providing a large, safe, carpeted work area that is 5 inches (12.7 cm) above the floor or other surface on which the Dolly is being used. These Boards can be installed on either one or both sides of the Dolly. The gap between the Front Boards for the Low Level Head (LH), Long Low Level Head (LLH) or Quick Change Low Level Head (LHT) can be filled with the Front Board Bridge (FBB) for additional standing area.
Front Pins
The Front Pins (FPIN) are used to disengage the Dolly's front spindles for use on Track. The Front Pins are stored in the Knee Bumper (BPR).
High Side Boards
High Side Boards (HTL, HTR) are used to give camera operators and/or assistants an additional carpeted work area. The Boards mount on the Dolly 15 inches (38.1cm) above the floor or other surface on which the Dolly is being used, flush with the carpeted standing areas. These Boards can be mounted on left (HTL), right (HTR) or both sides of the Dolly.
High Side Boards
High Side Boards (HTL, HTR) are used to give camera operators and/or assistants an additional carpeted work area. The Boards mount on the Dolly 15 inches (38.1cm) above the floor or other surface on which the Dolly is being used, flush with the carpeted standing areas. These Boards can be mounted on left (HTL), right (HTR) or both sides of the Dolly.
Hand Screw
The Hand Screw is used to secure the multi-position 4-way level head to the Dolly beam.
Low Side Boards
Low Side Boards (LT) are used to give camera operators and/or assistants an additional carpeted work area. The Boards mount on the Dolly 5 inches (12.7 cm) above the floor or other surface on which the Dolly is being used, flush with the Front Boards (F). When used in conjunction with the Front Boards (F) and a Front Board Bridge (FBB), it creates a walk-around platform for camera operators to safely move around the Dolly.
Power Cord
The Power Cord (PC) is used to charge the Dolly. It is a 125 volt, 13 amp, UL listed, AC, three-pronged (grounded) electrical cord. The Power Cord is 4 feet (121.92 cm) long.
Push Posts
Push Posts (PP) are used to push the Dolly and can be installed in any of the Dolly's eight sockets. Two Push Post sockets are located at the rear of the Dolly, two seat sockets are located on each side of the Dolly, and two seat sockets are located on the Dolly lift beam. The Push Posts also can be used as rear Carry Handles when placed in the lifting sockets located at the rear of the Dolly. Either Push Post can be used to operate the manual hydraulic hand pump when electrical power is unavailable.
Large Seat
The Large Seat (S) is a 12-inch (30.48 cm) diameter padded seat for the camera operator or assistant. With Teflon slides for smooth, easy movement on a polished chrome rail, the Seat laterally slides 10.5 inches (26.67 cm), pivots 360 degrees in the Seat socket and adjusts vertically up to 7 inches (17.78 cm).
4-way Level Head
The Standard Multi-Position Level Head (SLT) gives camera operators a wide range of camera mounting positions. The Head can be mounted forward or backward. When mounted forward, the head can be indexed in 30-degree increments, from 0 to 360 degrees. The leveling thumbscrews allow up to 13 degrees of four-way leveling adjustment in all directions. The Standard Multi-Position Level Head has a standard Mitchell mount.
Small Seat
The Small Seat (ST) is a 10-inch (25.4 cm) diameter padded seat for the camera operator or assistant. With Teflon slides for smooth, easy movement on a polished chrome rail, the Seat laterally slides 7 inches (17.78 cm), pivots 360 degrees in the Seat socket and adjusts vertically up to 7 inches (17.78 cm).
Pneumatic Tires
The Model 10 Dolly has eight wheels as standard equipment (4 TLW, large, and 4 TSW, small). These wheels have polyurethane covered rubber pneumatic tires, concentrically ground for smooth, steady performance.
Pneumatic Tires
The Model 10 Dolly has eight wheels as standard equipment (4 TLW, large, and 4 TSW, small). These wheels have polyurethane covered rubber pneumatic tires, concentrically ground for smooth, steady performance.
Model 10 Dolly
Full Rental Package
The Full Rental Package includes all the accessories from the Standard Rental Package, plus the additional items listed in the Full Rental Package table on the right.
Accessory Carts
New accessory carts for the Model 10 and 11 Dollies. A timesaving and efficient way to transport and store Dolly accessories from the grip truck to location. One cart for boards and one for other Dolly accessories. Designed for ease of use in many different terrains. The use of the two carts assures ease of movement and maneuverability.
4-way Low Level Head
The 4-way Low Level Head (LHT) is used on the J.L. Fisher Dolly Model 10 equipped with the Standard Multi-Position Level Head. It enables operators and/or assistants to position the camera lower than possible with standard heads. This head features four-way level adjustment with up to 8 degrees of tilt in all directions. The Model 10 Dolly 4-way Low Level Head (LHT) can be indexed in 30-degree increments, from 0 to 360 degrees, for Dutch angles or underslung camera positions. This Head has a single screw for quick changes.
90-Degree Angle Plate
The 90-Degree Camera Angle Plate (AP) enables camera operators to position the camera at a 90-degree angle from the Mitchell mount for straight-up or straight-down camera shots. The Angle Plate has a standard Mitchell mount that attaches to all J.L. Fisher Dollies and Mitchell mount products.
Diving Board, Left
Diving Boards (DTL, DTR) provide camera operators and/or assistants with additional carpeted work area that extends beyond the front of the Dolly. Diving Boards mount above the floor or other surface on which the Dolly is being used, flush with the carpeted standing areas on top of the Dolly (Model 10 Dolly 15 inches above). Diving Boards can be mounted on the left (DTL), right (DTR) or both sides of the Dolly.
Diving Board, Right
Diving Boards (DTL, DTR) provide camera operators and/or assistants with additional carpeted work area that extends beyond the front of the Dolly. Diving Boards mount above the floor or other surface on which the Dolly is being used, flush with the carpeted standing areas on top of the Dolly (Model 10 Dolly 15 inches above). Diving Boards can be mounted on the left (DTL), right (DTR) or both sides of the Dolly.
Front Board Bridge
The Front Board Bridge (FBB) is used when both Front Boards (F) are on the Dolly. Front Board Bridge fills the gap between the Front Boards, completing a large walk-around carpeted platform. Boards mount above the floor or other surface on which the Dolly is being used (Model 10 Dolly 5 inches above).
Rotating Offset
Rotating Offsets (RO, ROP, ROL, ROX, ROB) enable camera operators to easily change camera position with the lockable rotating mechanism. All models feature a 360-degree range with 84 lock positions (every 4.28 degrees) and a leveling indicator. These lightweight offsets have a standard Mitchell mount that attaches to all J.L. Fisher Dollies and Mitchell mount products. The Rotating Offset (RO) has a 6.25-inch offset and 5-inch riser and is equipped with a standard Mitchell mount.
Camera Riser, 6"
The Camera Riser (R6), extends the standard Mitchell mount on the Dolly or accessories by 6.5 inches. Risers increase the Dolly's maximum lift elevation. Manufactured from high-grade aluminum alloy, this Riser has a standard Mitchell mount that attaches to all J.L. Fisher Dollies and Mitchell mount products.
Camera Riser, 12"
The Camera Riser (R12), extends the standard Mitchell mount on the Dolly or accessories by 12.5 inches. Risers increase the Dolly's maximum lift elevation. Manufactured from high-grade aluminum alloy, this Riser has a standard Mitchell mount that attaches to all J.L. Fisher Dollies and Mitchell mount products.
Camera Offset, 10"
The Camera Offset (U) enables camera operators to offset the camera from its original position on the Dolly by 10 inches. Manufactured from high-grade aluminum alloy for stability, this lightweight Offset has a standard Mitchell mount that attaches to all J.L. Fisher Dollies and Mitchell mount products.
Camera Offset, 24"
The Camera Offset (TH) enables camera operators to offset the camera from its original position on the Dolly by either 12 inches or 24 inches. Two cameras can be simultaneously mounted on the TH offset. Manufactured from high-grade aluminum alloy for stability, this lightweight Offset has a standard Mitchell mount that attaches to all J.L. Fisher Dollies and Mitchell mount products.
Seat Offset, High
The Seat Offset High (SOH) mounts into the seat post sockets in the Dolly frame, and offsets the Dolly seat 45 degrees, giving camera operators and/or assistants flexibility in positioning themselves on the Dolly. The Seat Offset is equipped with a breakaway safety release.
Seat Offset, Straight
The Seat Offset Straight (SOS) mounts into the seat post sockets in the Dolly frame, and offsets the Dolly seat 90 degrees, giving camera operators and/or assistants flexibility in positioning themselves on the Dolly. The Seat Offset is equipped with a breakaway safety release.
Seat Riser
The Seat Riser (SR6) enables operators and/or assistants to increase the seat heights. The Seat Riser adjusts to four different height levels with a quick-release pullout pin on a locking collar.
Standing Platform
The Beam Step Standing Platform (BST), give the camera operators and/or assistants a safe, carpeted platform for making high shots. The platform mounts in the Dolly's lift beam seat mounts and is equipped with breakaway safety releases.
Part # | Description | Qty |
AC | Accessory Carts | 2 |
LHT | 4-way Low Level Head | 1 |
AP | 90-Degree Angle Plate | 1 |
DTL | Diving Board, Left | 1 |
DTR | Diving Board, Right | 1 |
FBB | Front Board Bridge | 1 |
RO | Rotating Offset | 1 |
R6 | Camera Riser, 6" | 1 |
R12 | Camera Riser, 12" | 1 |
U | Camera Offset, 10" | 1 |
TH | Camera Offset, 24" | 1 |
SOH | Seat Offset, High | 1 |
SOS | Seat Offset, Straight | 1 |
SR6 | Seat Riser | 1 |
BST | Standing Platform | 1 |